Yubico Forum

...visit our web-store at store.yubico.com
It is currently Tue Jan 30, 2018 2:01 pm

All times are UTC + 1 hour




Post new topic Reply to topic  [ 54 posts ]  Go to page Previous  1, 2, 3, 4, 5, 6  Next
Author Message
PostPosted: Fri Sep 27, 2013 3:05 pm 
Offline
Site Admin
Site Admin

Joined: Wed Nov 14, 2012 2:59 pm
Posts: 666
Yes, remove and plugin the Yubikey after settinging it in mode 82

Disable other smartcard readers then plugin the yubikey and try again,

_________________
-Tom


Top
 Profile  
Reply with quote  

Share On:

Share on Facebook FacebookShare on Twitter TwitterShare on Tumblr TumblrShare on Google+ Google+

PostPosted: Fri Sep 27, 2013 3:50 pm 
Offline

Joined: Wed Apr 28, 2010 8:32 pm
Posts: 6
OK, so I think things have been working since installing the .CAP file but what I've discovered is an issue with having my NEO on my keychain and trying to give it full contact with my GNex. After taking it off of my keyring and keeping it full flush against my phone it's working like it's supposed to. I'm going to have to put it on my key ring differently.


Top
 Profile  
Reply with quote  
PostPosted: Fri Sep 27, 2013 5:48 pm 
Offline

Joined: Mon Aug 01, 2011 10:27 pm
Posts: 16
Tom wrote:
Yes, remove and plugin the Yubikey after settinging it in mode 82

Disable other smartcard readers then plugin the yubikey and try again,


I set the mode to 82 on my mac, so re-inserting was definitely taken care of.

I just tried again with the Windows box. I went into the Device Manager, and found a device under the category "Memory technology driver" named "Realtek PCIE CardReader" as well as the controller for my SD slot, "SDA Standard Compliant SD Host Controller". I disabled both those devices and then attempted inserting the yubikey.

When I insert it, I get a new category under Device Manager, "Smart card readers", and the device installed is called "Microsoft Usbccid Smartcard Reader (WUDF)".

However, when I try to run GPShell, I still get the same error I described above, "The smart card is not responding to a reset".


Top
 Profile  
Reply with quote  
PostPosted: Fri Sep 27, 2013 6:03 pm 
Offline

Joined: Wed Apr 28, 2010 8:32 pm
Posts: 6
deinspanjer: Can you post a copy of your gpinstall.txt file?


Top
 Profile  
Reply with quote  
PostPosted: Fri Sep 27, 2013 6:15 pm 
Offline

Joined: Mon Aug 01, 2011 10:27 pm
Posts: 16
tnolte wrote:
deinspanjer: Can you post a copy of your gpinstall.txt file?


It is the default file from the ykneo-oath project with the install -file argument changed to point to the .cap file that is in the current working directory.

https://www.dropbox.com/s/ndpqv1ut9gg0vgi/gpinstall.txt


Top
 Profile  
Reply with quote  
PostPosted: Fri Oct 04, 2013 8:40 am 
Offline

Joined: Fri Oct 04, 2013 8:29 am
Posts: 3
Yeah, I'm getting the same "error 0x8010001D" as deinspanjer in Linux Mint 15, even after installing the files from the aforementioned PPA, setting mode 82 and power cycling, and checking for additional smartcard devices (there aren't any). Would it help any to build the GlobalPlatform files manually in case Klas' binary isn't working for me?


Top
 Profile  
Reply with quote  
PostPosted: Fri Oct 04, 2013 7:09 pm 
Offline

Joined: Fri Oct 04, 2013 8:29 am
Posts: 3
Whew! What an ordeal these past few hours have been =P You'll have to forgive my n00bness, but I accidentally set my neo to mode 81 and couldn't figure out how to get it back to 82 until I downloaded, built, and ran ykneo-ccid-modeswitch and installed pcscd. I believe the latter was what was missing initially, in case anyone was wondering. Once I reset to mode 82 and power cycled, the applet had no trouble downloading. Perhaps these potential pitfalls could be mentioned in the FAQ somewhere?


Top
 Profile  
Reply with quote  
PostPosted: Sun Nov 03, 2013 5:32 pm 
Offline

Joined: Mon Sep 23, 2013 2:12 pm
Posts: 4
I'm having hard time here with step 0...

I have set my NDEF configuration to be used with Lastpass. Will this applet disable/replace all that?


Top
 Profile  
Reply with quote  
PostPosted: Wed Nov 13, 2013 4:57 pm 
Offline

Joined: Mon Aug 01, 2011 10:27 pm
Posts: 16
I was finally able to set up one of my yubikeys using a different Windows computer.

I have some follow-up questions, but I'll post them in a new thread for clarity.


Top
 Profile  
Reply with quote  
PostPosted: Wed Nov 20, 2013 7:12 pm 
Offline

Joined: Mon Jul 29, 2013 12:10 pm
Posts: 15
Hi,
even though I was able to install the ykneo-oath cap file (ykneo-oath-0.2.1.cap) with gpshell in Ubuntu saucy (installing gpshell from ppa and installing pcscd was needed)

Android YubiOATH says "Empty credentials list" when I swipe the key but as soon as I try to scan Googles QR to move the 2nd Factor to it I get a

Error in Yubikey communication!

YubiOATH 0.1.6 on a Nexus 5 same with a Nexus 7 razorg, Yubikey Neo 3.0.4 Reports as Yubico Yubikey NEO OTP+CCID) ID 1050:0111 Yubico.com

What am I doing wrong?


Top
 Profile  
Reply with quote  
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 54 posts ]  Go to page Previous  1, 2, 3, 4, 5, 6  Next

All times are UTC + 1 hour


Who is online

Users browsing this forum: Heise IT-Markt [Crawler] and 6 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group